dell studio slim 540s manual

dell studio slim 540s manual

Watch this video for help in locating the source of the issue, and troubleshooting the most common causes in Windows 8, Windows 8.1 and Windows 10. Closed captions available in many languages. Watch this video for help in locating the source of the issue, and troubleshooting the most common causes in Windows 8, Windows 8.1 and Windows 10. Closed captions available in many languages. Page Count: 68 NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.Before Setting Up Y our Computer When positioning your computer, ensure that you allow easy access to a power source, adequate ventilation, and a level surface to place your computer. Restricting airflow around your Studio Slim 540s may cause it to overheat. T o prevent overheating ensure that you leave at least 10.2 cm (4 inches) at the back of the computer and a minimum of 5.1 cm (2 inches) on all other sides. Y ou should never put your computer in an enclosed space, such as a cabinet or drawer when it is powered on. The HDMI connector is a high-performance digital connector that carries both video and audio signals for displays such as TVs and monitors with integrated speakers. The VGA connector carries only video signals for displays such as monitors and projectors. NOTE: A DVI connector may be available on your computer if you purchased an optional discrete graphics card. -OR- Downloaded from www.Manualslib.http://hainescentreasia.com/images/deere-jx75-manual.xml

• dell studio slim d540s manual, dell studio slim 540s service manual pdf, dell studio slim 540s manual, dell studio slim 540s manual, dell studio slim 540s manual download, dell studio slim 540s manual pdf, dell studio slim 540s manual downloads, dell studio slim 540s manual free, dell studio slim 540s manual.

com manuals search engine Refer to the following table when identifying the connectors on your display to select the connection type you will use. HDMI VGA DVI Y ou can connect to the display using the following connectors available on your computer: the VGA connector, the HDMI connector, or the DVI connector (optional). Connect Using the VGA Connector If your display has a VGA connector, use a VGA cable (with blue connectors at both ends). If your display has a DVI connector, use the VGA cable (with blue connectors at both ends) with a VGA-to-DVI adapter (white plug). NOTE: Y ou can purchase a VGA-to-DVI adapter from the Dell website at dell.com. Connect Using a DVI Connector (Optional) Connect the display using a DVI cable. NOTE: Y ou can purchase additional HDMI and DVI cables from the Dell website at dell.com. Connect the Keyboard and Mouse Connect your keyboard and mouse to the USB connectors on the back panel of the computer. Use only an Ethernet cable (RJ45 connector). Do not plug a telephone cable (RJ11 connector) into the network connector. T o attach your computer to a network or broadband device, connect one end of a network cable to either a network port or a broadband device. Connect the other end of the network cable to the network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached. The screens will take you through several procedures including accepting license agreements, setting preferences, and setting up an Internet connection. NOTICE: Do not interrupt the operating system’ s setup process. Doing so may render your computer unusable. Connect to the Internet (Optional) NOTE: ISPs and ISP offerings vary by country. T o connect to the Internet, you need an external modem or network connection and an Internet service provider (ISP). Internet access through your existing telephone line or cellular telephone service.http://feng-huametal.com/userfiles/deere-js63-manual.xml

With a DSL connection, you can access the Internet and use your telephone on the same line simultaneously.Dial-up connections are considerably slower than DSL and cable (or satellite) modem connections. Y our computer does not have an integrated modem. An optional USB modem must be used for dialup service with your computer. NOTE: If an external USB modem or WLAN adapter is not part of your original order, you can purchase one from the Dell website at dell.com. Setting Up a Wired Internet Connection If you are using a dial-up connection, connect the telephone line to the external USB modem (optional) and to the telephone wall jack before you set up your Internet connection. Setting Up a Wireless Connection Before you can use your wireless Internet connection, you need to connect to your wireless router. Follow the instructions on the screen to 3. complete the setup. If you do not have an ISP icon on your desktop or if you want to set up an Internet connection with a different ISP, perform the steps in the following section. Contact your ISP to check the service status, or try connecting again later. NOTE: Have your ISP information ready. If you do not have an ISP, the Connect to the Internet wizard can help you get one. The Connect to the Internet window appears. NOTE: If you do not know which type of connection to select, click Help me choose or contact your ISP. Follow the instructions on the screen and 5. use the setup information provided by your ISP to complete the setup. Using Y our Studio Slim 540s 6 7 10 8 9 2 3 1 4 5 There may be a problem with either the system board or power supply. 7 USB 2.0 connectors (2) — Connects USB devices that are connected occasionally, such as memory keys, digital cameras, and MP3 players. 8 Headphone connector — Connects to headphones. A blinking blue light indicates hard drive activity. NOTICE: T o avoid loss of data, never turn off the computer while the hard drive activity light is blinking.

The drive automatically pulls the disc in and begins reading its content. T o eject a disc from the drive, press the eject button. A few seconds later the disc ejects. For more information, see “Back Panel Connectors” on page 18. 2 Card slots — Access connectors for any installed PCI and PCI Express cards. 3 Power supply LED — Indicates power availability for the power supply. NOTE: May or may not be available on your computer. 4 Power connector — Insert the power cable. 4 2 1 3 4 2 1 3 The network activity light flashes when the computer is transmitting or receiving data. On computers with a sound card, use the connector on the card. This format carries an audio signal without going through an analog audio conversion process. Y ou can also edit and view digital photographs and images. Check your purchase order for software installed on your computer. After connecting to the Internet, you can access websites, setup an e-mail account, upload and download files, and so on. Entertainment and Multimedia Y ou can use your computer to watch videos, play games, create your own CDs, and listen to music and radio stations. Y our optical disc drive may support multiple disc media formats including CDs, Blu-ray Discs (if the option is selected at the time of purchase), and DVDs. Y ou can download or copy pictures and video files from portable devices, such as digital cameras and cell phones. Optional software applications enable you to organize and create music and video files that can be recorded to disc, saved on portable products such as MP3 players and handheld entertainment devices, or played and viewed directly on connected TVs, projectors, and home theater equipment. Customizing the Desktop Y ou can customize your desktop to change the appearance, resolution, wallpaper, screensaver, and so on by accessing the Personalize appearance and sounds window. T o access the display properties window: Right-click an open area of the desktop. 1. Click 2.

Personalize, to open the Personalize appearance and sounds window and learn more about your customization options. Backing Up Y our Data It is recommended that you periodically back up files and folders on your computer.If you can not solve your problem using the following guidelines, see “Using Support T ools” on page 28 or “Contacting Dell” on page 43. CAUTION: Only trained service personnel should remove the computer cover. See the Service Manual on the Dell Support website at support.dell.com for advanced service and troubleshooting instructions. CAUTION: Before working inside your computer, read the safety information that shipped with your computer. Network Problems Wireless Connections If the network connection is lost — The wireless router is offline or wireless has been disabled on the computer.Follow the instructions on the screen c. to complete the setup. NOTE: The link integrity light on the network connector is only for the wired cable connection. The link integrity light does not provide status for wireless connections. Power Problems If the power light is off — The computer is either turned off or is not receiving power.Also bypass power protection devices, power strips, and power extension cables to verify that the computer turns on properly.Ensure that the display is properly connected and then turn it off, then back on. If the power light is blinking white — The computer is in standby mode. Press a key on the keyboard, move the pointer on the trackpad or a connected mouse, or press the power button to resume normal operation. If the power light is solid amber — The computer has a power problem or an internal device malfunction. For assistance contact Dell, see “Contacting Dell” on page 43. If the power light is blinking amber — The computer is receiving electrical power, but a device might be malfunctioning or incorrectly installed.

Y ou may have to remove and then reinstall the memory modules (for information on removing and replacing memory modules, see the Service Manual on the Dell Support website at support.dell.com ). If you encounter interference that hinders reception on your computer — An unwanted signal is creating interference by interrupting or blocking other signals.If necessary, install additional memory (see the Service Manual on the Dell Support website at support.dell.com ). Y our computer supports DDR2 memory. For more information about the type of memory supported by your computer, see “Specifications” on page 25. Diagnostics” on page 31 ). Service Manual on the Dell Support website at support.dell.com ) to ensure that your computer is successfully communicating with the memory. Lockups and Software Problems If the computer does not start up — Ensure that the power cable is firmly connected to the computer and to the electrical outlet. If a program stops responding — End the program: Press simultaneously. 1. Click 2. Applications. Click the program that is no longer 3. responding. Click 4. End T ask. If a program crashes repeatedly — Check the software documentation. If necessary, uninstall and then reinstall the program. NOTE: Software usually includes installation instructions in its documentation or on CD. T urn the computer off. If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Then restart your computer. In the welcome screen, click 2. Next. Follow the instructions on the screen. 3. If a solid blue screen appears — T urn the computer off. If you are unable to get a response by pressing a key on your keyboard or moving your pointer or mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Then restart your computer.

For more information about Dell Support Center and available support tools, click the Services tab at support.dell.com. Click the icon in the taskbar to run the application. For more information about the Dell Support Center, see the Dell T echnology Guide on your hard drive or on the Dell Support website at support.dell.com. CAUTION: T o guard against the likelihood of electric shock, laceration by moving fan blades or other unexpected injuries, always unplug your computer from the electrical outlet before removing the cover. Using Support T ools NOTE: If the message you received is not listed in the following examples, see the documentation for either the operating system or the program that was running when the message appeared. Alternatively you could see the Service Manual on the Dell Support website at support.dell.com or see “Contacting Dell” on page 43 for assistance. For help in resolving this problem, please note this checkpoint and contact Dell T echnical Support — The computer failed to complete the boot routine three consecutive times for the same error (see “Contacting Dell” on page 43 for assistance). CMOS checksum error — Possible motherboard failure or RTC battery low. Replace the battery. See the Service Manual on the Dell Support website at support.dell.com or see “Contacting Dell” on page 43 for assistance. CPU fan failure — CPU fan has failed. Replace the CPU fan. See the Service Manual on the Dell Support website at support.dell.com. Hard-disk drive failure — Possible hard disk drive failure during HDD POST (see “Contacting Dell” on page 43 for assistance). Hard-disk drive read failure — Possible hard disk drive failure during HDD boot test (see “Contacting Dell” on page 43 for assistance). Keyboard failure — Keyboard failure or loose cable. No boot device available — No bootable partition on hard disk drive, the hard disk drive cable is loose, or no bootable device exists. USB over current error — Disconnect the USB device.

Y our USB device needs more power for it to function properly. Use an external power source to connect the USB device, or if your device has two USB cables, connect both of them. NOTICE - Hard Drive SELF MONITORING SYSTEM has reported that a parameter has exceeded its normal operating range. Dell recommends that you back up your data regularly. A parameter out of range may or may not indicate a potential hard drive problem — S.M.A.R.T error, possible hard disk drive failure. This feature can be enabled or disabled in the BIOS setup (see “Contacting Dell” on page 43 for assistance). Hardware T roubleshooter If a device is either not detected during the operating system setup or is detected but incorrectly configured, you can use the Hardware T roubleshooter to resolve the incompatibility. In the search results, select the option that 3. best describes the problem and follow the remaining troubleshooting steps. It is recommended that you print these procedures before you begin. NOTE: Dell Diagnostics works only on Dell computers. NOTE: The Drivers and Utilities media is optional and may not ship with your computer. See the System Setup section in the Service Manual to review your computer’ s configuration information, and ensure that the device that you want to test displays in the system setup program and is active. Start the Dell Diagnostics from your hard drive or from the Drivers and Utilities media. Starting Dell Diagnostics From Y our Hard Drive The Dell Diagnostics is located on a hidden diagnostic utility partition on your hard drive. NOTE: If your computer cannot display a screen image, see “Contacting Dell” on page 43. Ensure that the computer is connected to an 1. electrical outlet that is known to be working properly. Select Diagnostics from the boot menu and press. NOTE: If you see a message stating that no diagnostics utility partition has been found, run the Dell Diagnostics from the Drivers and Utilities media.

Starting Dell Diagnostics From the Drivers and Utilities Media Insert the 1. Drivers and Utilities media. Shut down and restart the computer. 2. When the DELL logo appears, press immediately. NOTE: The next steps change the boot sequence for one time only. On the next start-up, the computer boots according to the devices specified in the system setup program. Select the 4. Boot from CD-ROM option from the menu that appears and press. T ype 1 to start the CD menu and press 5. to proceed. Select 6. Run the 32 Bit Dell Diagnostics from the numbered list. If multiple versions are listed, select the version appropriate for your computer. When the Dell Diagnostics 7. Main Menu appears, select the test you want to run. Use System Restore as the first solution for restoring your operating system and preserving data files. This procedure permanently delete all data on the hard drive and remove any programs installed after you received the computer. Use Dell Factory Image Restore only if System Restore did not resolve your operating system problem.However, using the Op er at in g Sy st em d is c al so d el et es a ll d a ta o n th e ha rd dr iv e. U se t he d is c on ly i f Sy s te m Re st or e di d not resolve your operating system problem. System Restore The W ind ows op era tin g s yst ems pr ovi de a S yst em Restore option which allows you to return your computer to an earlier operating state (without affecting data files) if changes to the hardware, sof tw are, o r o the r s yst em set tin gs hav e l eft th e computer in an undesirable operating state. Any changes that System Restore makes to your computer are completely reversible. NOTICE: Make regular backups of your data files. System Restore does not monitor your data files or recover them. System Recovery Options NOTE: The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to continue the desired action. Click 3.

Next and follow the remaining prompts on the screen. In the event that System Restore did not resolve the issue, you may undo the last system restore. Undoing the Last System Restore NOTE: Before you undo the last system restore, save and close all open files, and exit any open programs. Do not alter, open, or delete any files or programs until the system restoration is complete. Click 1. Start. In the 2. Start Search box, type System Restore and press. Click 3. Undo my last restoration and click Next. Dell Factory Image Restore NOTICE: Using Dell Factory Image Restore permanently deletes all data on the hard drive and removes any programs or drivers installed after you received your computer. If possible, back up the data before using these options. Use Dell Factory Image Restore only if System Restore did not resolve your operating system problem. NOTE: Dell Factory Image Restore may not be available in certain countries or on certain computers. Use Dell Factory Image Restore only as the last method to restore your operating system. These options restore your hard drive to the Any programs or files added since you received your computer—including data files—are permanently deleted from the hard drive. Data files include documents, spreadsheets, e-mail messages, digital photos, music files, and so on. If possible, back up all data before using Factory Image Restore. Dell Factory Image Restore T urn on the computer. When the Dell logo 1. appears, press several times to access the Vista Advanced Boot Options Window. Select 2. Repair Y our Computer. The 3. System Recovery Options window appears. Select a keyboard layout and click 4. Next. T o access the recovery options, log on as a 5. local user. T o access the command prompt, type administrator in the User name field, then click OK. Click 6. Dell Factory Image Restore. The Dell Factory Image Restore welcome screen appears.

NOTE: Depending upon your configuration, you may need to select Dell Factory T ools, then Dell Factory Image Restore. Click 7. Next. The Confirm Data Deletion screen appears. NOTICE: If you do not want to proceed with Factory Image Restore, click Cancel. Click the checkbox to confirm that you want 8. to continue reformatting the hard drive and restoring the system software to the factory condition, then click Next. The restore process begins and may take five or more minutes to complete. A message appears when the operating system and factory-installed applications have been restored to factory condition. Click 9. Finish to reboot the system. If Device Driver Rollback does not resolve the problem, then use System Restore to return your operating system to the operating state it was in before you installed the new device driver. See “Using Microsoft Windows System Restore” on page 33. NOTICE: Before performing the installation, back up all data files on your primary hard drive. For conventional hard drive configurations, the primary hard drive is the first drive detected by the computer.Use the Dell Drivers and Utilities media to load any required drivers. Depending on the region from which you ordered your computer, or whether you requested the media, the Dell Drivers and Utilities media and Operating System media may not ship with your computer. Reinstalling Windows Vista The reinstallation process can take 1 to 2 hours to complete. After you reinstall the operating system, you must also reinstall the device drivers, virus protection program, and other software. Save and close any open files and exit any 1. open programs. Insert the 2. Operating System media. Click 3. Exit if the Install Windows message appears. On the next start-up, the computer boots according to the devices specified in the system setup program. Press any key to 7. Boot from CD-ROM. Follow the instructions on the screen to complete the installation. See “Dell Diagnostics” on page 2.

31 for procedures on how to run Dell Diagnostics. Fill out the “Diagnostic Checklist” on 3. page 42. Use Dell’ s extensive suite of online services 4. available at Dell Support ( support.dell.com ) for help with installation and troubleshooting procedures. See “Online Services” on page 39 for a more extensive list of Dell Support online. If the preceding steps have not resolved the 5. problem, see “Contacting Dell” on page 43. NOTE: Call Dell Support from a telephone near or at the computer so that the support staff can assist you with any necessary procedures. NOTE: Dell’ s Express Service Code system may not be available in all countries. When prompted by Dell’ s automated telephone system, enter your Express Service Code to route the call directly to the proper support personnel. If you do not have an Express Service Code, open the Dell Accessories folder, double-click the Express Service Code icon, and follow the directions. NOTE: Some of the following services are not always available in all locations outside the continental U.S. Call your local Dell representative for information on availability. Getting Help Dell’ s support staff uses computer -based diagnostics to provide fast, accurate answers. For more information, go to support.dell.com and click DellConnect.For instructions on accessing the telephone number to call your region, see “Contacting Dell” on page 43. Automated Order -Status Service T o check on the status of any Dell products that you have ordered, you can go to support.dell. com, or you can call the automated order - status service. A recording prompts you for the information needed to locate and report on your order. For the telephone number to call your region, see “Contacting Dell” on page 43. If you have a problem with your order, such as missing parts, wrong parts, or incorrect billing, contact Dell for customer assistance. Have your invoice or packing slip handy when you call.

For the telephone number to call for your region, see “Contacting Dell” on page 43. Returning Items for Repair Under W arranty or for Credit Prepare all items being returned, whether for repair or credit, as follows: Call Dell to obtain a Return Material 1. Authorization Number, and write it clearly and prominently on the outside of the box. For the telephone number to call for your 2. region, see “Contacting Dell” on page 43. Include a copy of the invoice and a letter 3. describing the reason for the return. Include a copy of the Diagnostics Checklist 4. (see “Diagnostic Checklist” on page 42 ), indicating the tests that you have run and any error messages reported by the Dell Diagnostics (see “Dell Diagnostics” on page 31). Include any accessories that belong with 5. the item(s) being returned (power cables, software, guides, and so on) if the return is for credit. Pack the equipment to be returned in the 6. original (or equivalent) packing materials. Y ou are responsible for paying shipping 7. expenses. Y ou are also responsible for insuring any product returned, and you assume the risk of loss during shipment to Dell. Collect On Delivery (C.O.D.) packages are not accepted. Returns that are missing any of the 8. preceding requirements will be refused at Dell’ s receiving dock and returned to you. The code helps Dell’ s automated-support telephone system direct your call more efficiently. Y ou may also be asked for your Service T ag (located on the top of your computer towards the back). Remember to fill out the following Diagnostics Checklist. If possible, turn on your computer before you call Dell for assistance and call from a telephone at or near the computer. Y ou may be asked to type some commands at the keyboard, relay detailed information during operations, or try other troubleshooting steps possible only at your computer. Ensure that your computer’ s documentation is available.If the computer is connected to a printer, print each file.

Otherwise, record the contents of each file before calling Dell.NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone- based support and service options. A vailability varies by country and product, and some services may not be available in your area. Select the appropriate service or support link 4. based on your need. Choose the method of contacting Dell that is 5. convenient for you. Check your warranty and return policies before working inside your computer. NOTE: Offerings may vary by region.Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. You can set a one-time-only boot sequence without entering the system setup program. 1 Shut down the computer through the Start menu. 2 Turn on the computer. When the DELL logo appears, press immediately. If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop, then shut down your computer and try again. 3 When the boot device list appears, highlight the device from which you want to boot and press. The computer boots to the selected device. The next time you reboot the computer, the previous boot order is restored. Changing Boot Sequence to a USB Device. If you wait too long and the operating system logo appears, continue to wait until you see the Windows desktop, then shut down your computer and try again. 4 The Boot Menu appears, listing all available boot devices. 5 Use the arrow keys to select the appropriate device (for the current boot only). NOTE: To boot to a USB device, the device must be bootable. To ensure that a device is bootable, check the device documentation. Changing the BIOS Settings.

The BIOS is a utility that serves as an interface between the computer hardware and the operating system. The BIOS settings may need to be updated for certain hardware replacements. 310. System Setup When the DELL logo appears, press To ensure that a The BIOS settings may need to be. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Dell Studio 540S. To start viewing the user manual Dell Studio 540S on full screen, use the button Fullscreen. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Dell Studio 540S but the selected pages only. paper. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.Before Setting Up Your Computer When positioning your computer, ensure that you allow easy access to a power source, adequate ventilation, and a level surface to place your computer. To prevent overheating ensure that you leave at least 10.2 cm (4 inches) at the back of the computThe HDMI connector is a high-performance digital connector that carries both video and audio signals for displays such as TVs and monitors with integrated speakers. The VGA connector carries only video signals for displays such as monitors and projectors. -OR- NOTE: A DVI connector may be available on your computer if you purchased an optional dRefer to the following table when identifying the connectors on your display to select the connection type you will use.